Guide · consumption and costs

Power consumption of a construction dehumidifier: what does it cost per day?

A construction dehumidifier runs day and night, so it is fair to ask what that costs. The sum is simple: power rating times hours times days times your price per kWh.

We size the machine to the volume of your room. That is why we install 0.75 kW where a hire company puts in 2.1 kW as standard. That is 64% less electricity for the same drying.

Carefree drying: the construction dehumidifier runs, you do not have to do a thing
64% less electricitythan a standard 2.1 kW construction dehumidifier
0.75kW
Power input of the Boost
18kWh
At most per 24 hours, continuously at full power
€0.30/kWh
Example price to calculate with, not a rate of ours
24h
Running per day: every hour of standstill costs drying time

How to work out the consumption

Every electrical appliance has a power input, expressed in kilowatts (kW). That figure is on the rating plate and in the technical data sheet. The consumption in kilowatt hours (kWh) is that power times the number of hours the machine runs. The cost is that consumption times your price per kWh:

kW × 24 hours × number of days × price per kWh = electricity cost

The result is an upper limit. A condensation construction dehumidifier has a humidistat: as soon as the humidity reaches the target value, the compressor throttles back and the machine uses much less. In the first days of a drying job, when a lot of moisture is released, you are close to that upper limit; towards the end, well below it.

Per machine

The power rating of our machines

The power input as stated in the technical data sheet on the machine page, with the maximum consumption per 24 hours and the cost per day at an example price of €0.30 per kWh. That price is only an example to calculate with; your own rate is on your energy bill and may be higher or lower.

Maximum consumption at continuous full power. Example price €0.30/kWh, not a Vernast rate.
MachinePowerMax. kWh per 24 hMax. per day (example)
BoostCondensation dehumidifier0.75 kW18 kWh€5.40
PerformanceCondensation dehumidifier1.1 kW26.4 kWh€7.92
UltimateCondensation dehumidifier1.4 kW33.6 kWh€10.08
RevolutionDesiccant dehumidifier · targeted drying0.42 kW10.1 kWh€3.02
HighflowSite fan · air circulation0.2 kW4.8 kWh€1.44
TurboflowSite fan · targeted drying1.2 kW28.8 kWh€8.64
Heatpower 30Electric site heater30 kW720 kWh€216.00
Heatboost 20Electric site heater20 kW480 kWh€144.00
For the site heaters that upper limit is mostly theoretical: their thermostat switches off as soon as the room is up to temperature, and how much they run after that depends on how well the building holds its heat. Even so, the heater is almost always the biggest consumer on site. So only heat where it is needed, such as in a cold cellar or on a winter site.
Worked example

What the electricity costs per day.

Alongside you can see what one machine costs in electricity per 24 hours if it runs non-stop at full power: our Boost next to two construction dehumidifiers from competitors, all calculated at the same example price of €0.30 per kWh.

These are upper limits. The humidistat throttles the compressor back as soon as the target humidity is reached, so in the second week the bill is lower than in the first. What does not change is the ratio: a machine with three times the power also costs three times as much electricity, every single day, whether it needs that capacity or not.

The grey bar at the bottom is different from the three above it: that is the hire of the Boost, €10.89 incl. VAT per day (see all prices). It is there for scale, so you can see straight away how electricity and hire compare.

Boost, our smallest construction dehumidifier€5.40
Dryfast DF 400, 1.4 kW€10.08
Dryfast DF 800, 2.1 kW€15.12
Hire of the Boost per day€10.89 incl. VAT

If you add a fan, relatively little consumption is added; a site heater weighs much more heavily. The power ratings of the Dryfast DF 400 and the Dryfast DF 800 come from their distributors' data sheets.

Two weeks of drying, step by step

0.75 kW × 24 hours18kWh/day
14 days252kWh
€0.30 per kWh€75.60electricity
Say you dry a new-build home with one Boost for two weeks, and the machine runs non-stop at full power. At the example price of €0.30 per kWh that is the upper limit: at most €5.40 per day. Thanks to the humidistat, the actual bill is lower.
The same fourteen days with a Dryfast DF 400, a competitor's construction dehumidifier of 1.4 kW, cost €141.12 in electricity, €65.52 more for the same room.
Frequently asked questions

All about the consumption of a construction dehumidifier

Is your question not listed?

Our drying experts will help you straight away, with advice tailored to your situation.

Multiply the power input by 24 hours. Our Boost draws 0.75 kW; that is at most 18 kWh per 24 hours if it runs non-stop at full power. In practice it is lower, because the humidistat throttles the machine back as soon as the target humidity is reached.

Multiply the kWh per day by your price per kWh. At an example price of €0.30 per kWh, the Boost costs at most €5.40 a day in electricity. Your own price is on your energy bill.

Yes. A construction dehumidifier is made to run day and night, and it has to: every hour it stands still lets the humidity in the air rise again. If it drains the water through a hose or a condensate pump rather than into a tank, it also keeps running over the weekend without you having to empty anything.

A construction fan uses less than a construction dehumidifier. An electric site heater uses much more: it produces heat, and that takes the most energy. Its thermostat does throttle back as soon as the room is up to temperature.

The power input is the consumption per hour. Our Boost is rated at 0.75 kW, so 750 watts per running hour. In our range that goes from 200 watts for a construction fan to 1,400 watts for the largest condensation dehumidifier; larger hire machines reach 2,100 watts.

Multiply the daily consumption by the number of days. Our Boost comes to at most 126 kWh per week (€37.80) and 540 kWh per month (€162.00) at an example price of €0.30 per kWh. Those are upper limits: the humidistat throttles the machine back as soon as the target value is reached, and a drying job rarely lasts a full month.

Yes. Our condensation construction dehumidifiers run on 230 V and plug into an ordinary socket. Do watch the circuit, though: an ordinary 16 A circuit can handle about 3.6 kW, so add up the power of everything connected to it. With 0.75 kW for the Boost there is room left for other tools. The stand-alone 20 and 30 kW site heaters, however, run on 400 V three-phase power and need their own connection.

Yes, and that makes sense. A household dehumidifier runs a few hours a day at low power to keep a living room comfortable. A construction dehumidifier runs day and night and has to pull dozens of litres of construction moisture out of the air every 24 hours. So it uses more per day, but it is only needed for a few weeks.

Per hour, yes, and that is exactly why size matters. A machine for volumes up to 800 m³ draws 2.1 kW, compared with 0.75 kW for a machine up to 250 m³. Put that large machine in a small room and you pay every day for capacity that cannot be used. That is why the drying calculator chooses the volume first and only then the machine.

Machine against machine

You do not put a large machine in a small room.

The biggest electricity bill rarely comes from an inefficient machine, but from an oversized one. Below, our smallest construction dehumidifier next to the Dryfast DF 800, the model most hire companies send out as standard, even to a cellar or a flat it is far too heavy for.

Our machine

Boost

Condensation dehumidifier for rooms up to 250 m³ · 230 V

18kWh per 24 hours

€5.40 per day in electricity at €0.30 per kWh

Power input0.75 kW
Moisture extraction50 L/day
Recommended volumeup to 250 m³
Electricity over two weeks€75.60

View the Boost

Comparison machine

Dryfast DF 800

The construction dehumidifier found in the range of most hire companies

50.4kWh per 24 hours

€15.12 per day in electricity at €0.30 per kWh

Power input2.1 kW
Moisture extraction150 L/day
Recommended volumeup to 800 m³
Electricity over two weeks€211.68
Saves €136.08 in electricity over two weeks: 64% less consumption, for a room where 250 m³ of capacity is enough. That is why the drying calculator works out your volume first and only then chooses the machine.
To be fair: the Dryfast DF 800 is not a bad machine. It is built for industrial work and for volumes up to 800 m³, and in a hall or warehouse like that it does exactly what it should. The problem starts when that same machine is put in a cellar, a flat or a single floor, and that happens often, because hire companies simply send out whatever is on the van. You then pay every day for capacity that cannot be used. So the point above is about size, not quality. Our figures come from the technical data sheet on the machine page (moisture extraction at 30 °C and 80% relative humidity), those for the Dryfast DF 800 from the distributor's product data sheet. In both cases the consumption is the power input times 24 hours, converted at the example price of €0.30 per kWh.
In practice

What pushes consumption up or down.

Five things determine whether you are close to that upper limit or stay well below it.

How wet the building is

As long as a lot of moisture is being released, the compressor runs almost continuously. As the screed and plaster dry out, the humidistat throttles back more often.

The temperature

In a cold room a condensation dehumidifier works less efficiently and runs longer for the same result. You can read why in condensation or desiccant dehumidifier.

An open house

Windows on tilt or an open door to a damp cellar keep letting in fresh moist air. The construction dehumidifier then dries the outside air instead of your walls.

The right size

A machine that is too small runs at full power for weeks; a properly sized machine finishes sooner. The drying calculator works out what suits your floor area.

The drying time itself

The biggest saving is a shorter drying time. How long screed and plasterwork need is explained in how long screed takes to dry.

Day and night

Can a construction dehumidifier run 24 hours a day and overnight?

Yes, and that is the whole idea. If you switch it off at night, the humidity rises again within a few hours and the moisture in the air soaks back into the walls and the floor. You then lose more drying time than you save in electricity.

Leave it running

A construction dehumidifier is built for continuous use.

  • Every hour of standstill counts. The humidity rises again within a few hours, and the moisture soaks back into walls and floor.
  • The humidistat regulates itself. As soon as the target value is reached, the compressor throttles back; you do not have to switch the machine off yourself.
  • Running continuously is usually cheaper. An extra day of hire weighs more heavily than the electricity for running through the night.
  • We measure before and after. In a drying package the technician records the start and end readings, so nobody has to decide on gut feeling.
Applies to every condensation machine in our range.
What to watch out for

Three things with continuous use.

  • Draining the water. With a tank you have to empty it regularly, otherwise the machine stops. With a hose to a drain, or a condensate pump (€2.42 incl. VAT per construction dehumidifier per day with us), drying carries on overnight and at the weekend too.
  • A clear spot. Do not put the machine against a wall or under a table; the air must be able to flow in and out freely.
  • The electrical circuit. An ordinary 16 A circuit at 230 V can handle about 3.6 kW. Add up the power of everything connected to it. The stand-alone Heatboost 20 and 30 T site heaters run on 400 V three-phase power and need their own connection; the heater in a drying package runs on an ordinary 230 V socket.
Rather not do the maths yourself?

In a drying package, nothing runs more than it needs to.

Our technicians place the machines, set the target value and measure the moisture before and after. So nothing runs harder or longer than it needs to. See also delivery and installation.

Calculate your drying package
Vernast technician giving a thumbs up
Any more questions about this?

Our drying specialists will work it out with you.

Not sure whether your circuit can cope, or which machine is the most efficient for your project? Ask your question and a specialist will reply within one working day.

We only use your details to answer your question. Rather have a price straight away? Calculate your drying package.
03 689 90 65